A useful custom forged wheel RFQ records the vehicle, brakes, wheel dimensions, mounting details, load requirement, finish and quantity in one reviewable specification. The supplier should return an identified proposal, the applicable fitment information and a clear release status. Copy the field sheet below, then keep technical approval separate from the appearance decision.
The order begins with a vehicle, not a wheel photograph
I start a custom wheel brief with the car the wheels will actually meet. You can choose a spoke design from a photograph, but I can't use that photograph to establish your vehicle configuration. I want the exact variant and a clear distinction between what is fitted now and what will be fitted at installation. Are your brakes staying? Is your suspension changing? If you haven't settled those questions, I leave them open in the request. That isn't an obstacle to discussing appearance. It's a way to keep an appearance discussion from authorizing machining against a vehicle description that no longer applies. The template below follows that distinction from the first request to the release. In a hypothetical order, the initial message asked for a particular spoke style and finish. The next revision added the exact vehicle variant and a note that the brakes would be replaced before installation. That single clarification changed the status of the request: it was no longer ready to approve from a stock-vehicle fitment assumption. No wheel had to be rejected and no customer outcome is claimed here. The example shows the document’s job. It makes an unresolved condition visible while the supplier can still ask for the information needed to review it.
The vehicle description changed. The release status had to change with it.
A specification needs a known vehicle state
You can settle what you like while the supplier reviews what your vehicle requires. Keep those decisions distinct in the order. The example follows a proposed document through that review; it doesn't claim that a real car was fitted or tested. Your completed record should make the same distinction visible to the installer.
Copy this custom forged wheel RFQ
The field sheet combines buyer-provided details with the supplier response needed to complete the order. BC Forged’s ordering form explicitly asks for the vehicle, brakes, ride height, wheel setup and finish; its TR01 specification also identifies vehicle-specific center bores. Forgeline’s installation guide adds mounting compatibility, clearance and the load-rating check. The sheet is an editorial purchasing template, not a universal engineering specification.
| Field | Buyer submits | Supplier confirms or returns |
|---|---|---|
| Vehicle | Year, make, model, trim; final modification state: [enter]. | Exact application reviewed: [enter]. |
| Wheel size | Requested diameter and width, front/rear: [enter]. | Supported sizes and construction: [enter]. |
| Bolt pattern | PCD and hole count, with units: [enter]. | Machined pattern and attachment compatibility: [enter]. |
| Offset | Requested ET or fitment objective: [enter]. | Reviewed offset/backspacing and drawing revision: [enter]. |
| Center bore | Known hub information or measurement status: [enter]. | Required bore and locating arrangement: [enter]. |
| Brake clearance | Exact brake package; drawings/template status: [enter]. | Information reviewed and checks remaining: [enter]. |
| Load rating | Vehicle/use and applicable load requirement: [enter]. | Rating for each proposed wheel variant: [enter]. |
| Finish | Color, treatment and component choices: [enter]. | Finish specification and any options: [enter]. |
| Quantity | Total and front/rear split; spare if needed: [enter]. | Quoted units, quantities and included hardware: [enter]. |
| Approval | Technical owner and installer: [enter]. | Open questions, accepted version and manufacturing release: [enter]. |
| Destination | Country, delivery address/postcode and receiving site: [enter]. | Quoted delivery area and freight/tax exclusions: [enter]. |
| Target timing | Required arrival date and any project milestone: [enter]. | Production lead time, release event and transit estimate: [enter]. |
| Packaging | Protection, carton/pallet and marking needs: [enter]. | Included packing and any separately quoted work: [enter]. |
| Trade terms | Requested trade term and named place: [enter]. | Quoted term, named place and allocation of charges: [enter]. |
| Quote validity | Planned approval date: [enter]. | Expiry date and conditions for repricing: [enter]. |
The destination and invoice-review fields are consistent with BC Forged’s published ordering sequence. The additional timing, packaging, trade-term and validity fields are buyer questions in this editorial RFQ, not claims that the manufacturer offers a particular arrangement. They let a sourcing team request an order-specific response without turning the article into a generic shipping manual.
What should come back with the quotation?
You should receive an identifiable proposal rather than only an acknowledgement of your preferred style. Look for the wheel design and construction, quoted front and rear specifications, fitment information reviewed, finish, quantity, exclusions and approval status. BC Forged describes invoice review followed by cross-section profile drawings at a later stage of its ordering sequence. That is a useful example of a document returned by a manufacturer, but its timing is a company policy, not a required sequence for every supplier. Record the stages your actual manufacturer uses.
Fill the sheet from the final vehicle configuration
I read a revision by asking what changed and which earlier answer it affects. If you've changed the width, has the supplier reviewed the new proposal? If you've changed the brakes, is the original fitment response still applicable? You shouldn't have to reconstruct the order from scattered messages. I keep the current vehicle description and wheel request together, then name the version being accepted. That gives your installer something definite to receive. It also lets you discuss a design change without quietly carrying forward an approval that belonged to another configuration. The document is useful when you can see why a value is there and who has confirmed it. In a FitmentSource custom forged wheels brief, I would keep that approved version with the sourcing request rather than imply that the sourcing label itself supplies an engineering approval. When selecting construction, the one-piece, two-piece and three-piece comparison explains what the supplier is being asked to manufacture. For the commercial side of the same RFQ, the forged wheel price guide separates per-wheel listings, set prices and unquoted charges. Use those articles for those decisions; keep this sheet focused on the data and approvals that belong to your order.
Keep unknown dimensions visibly unresolved
I leave unknown dimensions unknown. If you don't have an established offset or the clearance information your supplier needs, ask how to obtain it. Don't fill a blank with a number from another owner's car simply because it looks precise. I distinguish an approved value from your preference and from a value awaiting review. You can then see which decisions are yours and which need a technical response. That distinction also protects the meaning of your finish approval: you've accepted the appearance, not silently confirmed every dimension in an attachment. A complete-looking form isn't the goal. A request whose open questions are visible is more useful.
Read a completed approval status
Return to the hypothetical order. Its final review copy retained the chosen spoke style but marked the brake change as unresolved. The finish could be accepted as an appearance preference; machining remained on hold until the supplier had reviewed the relevant configuration. A later version would need to identify the reviewed dimensions and the remaining installation checks. This is a proposed way to complete the document, not a report that a real wheel was built or successfully fitted. Its value is that the record distinguishes progress in the design from completion of the fitment review.
A compact handoff can say: vehicle and brake package identified; proposed front and rear dimensions attached; manufacturer review pending; finish accepted; machining not released. After the outstanding review, replace the pending status with the accepted specification version and name the remaining installation checks. This is a hypothetical document example. It lets the buyer, manufacturer and installer see the same status without inventing a fitted vehicle or a successful test. In a FitmentSource custom forged wheel request, that clear handoff is the practical sourcing deliverable.
Appearance can be settled while fitment remains open
A custom finish is an important part of the order, but its approval answers an appearance question. Before release, the final document should show that the technical specification was reviewed in its current version and that the intended installer understands any checks still required. If the vehicle changes afterward, the earlier review should be revisited with the supplier. The order then closes the loop it opened: a wheel photograph expressed a preference; a vehicle-specific specification expresses what is actually being ordered.
Submit a complete field sheet, receive a specific proposal, and release the version that was actually reviewed. The sourcing work is complete when each party can identify the same order and the checks still assigned to it.
Frequently asked questions
Does a matching bolt pattern guarantee brake clearance?
No. Forgeline lists mounting compatibility checks and then calls for a hub test fit to confirm clearance. A matching bolt pattern answers only part of the fitment question.
What vehicle changes belong in a custom wheel order?
Identify changes relevant to the final installation, including planned brake and suspension changes. Ask the supplier what measurements or drawings it needs for that exact configuration.
Should finish approval release a wheel for machining?
Only if the technical specification and release responsibilities are also settled. Keep appearance approval distinct from the supplier’s fitment review so an accepted color cannot conceal an unresolved dimension.
Comment on this article
For a private product or quotation requirement, send a sourcing inquiry.